MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 33

Page: 33 / 204

Media Storage and Handling

What should I watch out for when loading labels?

Do not use label sheets that

„

Have labels that easily peel off

„

Have the backing sheets that have peeled away or have exposed
adhesive

Labels may stick to the fuser, causing them to peel off and media jams to
occur.

„

Are precut

Use label sheets that are

„

Recommended for laser printers

What should I watch out for when loading postcards?

Do not use postcards that are

„

Coated

„

Warped

„

Designed for inkjet printers

„

Multicolored

„

Preprinted or multicolored (may result in printer jamming)

Use postcards that are

„

Japanese Post Office standard postcards (3.9 x 5.8:” [100 x 148 mm])
recommended for laser printers

What should I watch out for when loading transparencies?

Attention

Use only the MINOLTA-QMS-approved transparencies. Check
www.minolta-qms.com/support (click on Answer Base) for currenlyt
approved media. To order approved media, go to www.q-shop.com.

Shiny backed paper

Paper cut into labels

Full page labels
(uncut)

Do not use

OK to use

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands

MINOLTA-QMS ENord magicolor 3100, User Manual

Search results

Summary of Contents for ENord magicolor 3100

Reviews:

Brands by name

Popular brands