manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 21

Replacing the Imaging Unit 

15

9

Remove the black protective sheet.

Attention

Do not touch black transfer rollers. They are extremely sensitive to 
hand oils and scratches, both of which reduce print quality. This 
type of damage is not covered by the product warranty.

10

Close the covers 

c

, 

d

.

11

Turn on the printer.

5

"

You do not need to reset the 
consumables usage monitor-
ing system when you replace 
an imaging unit.

After approximately 6 minutes warmup (assuming normal temperature 
and humidity), your printer prints a startup page and displays “

IDLE

” on 

the message window. 

This 6-minute warmup only happens when a new imaging unit has been 
installed. Normal time to warm up is approximately 1½ minutes.

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands