manualshive.com logo in svg

MINOLTA-QMS ENord magicolor 3100, User Manual

Share
Download
MINOLTA-QMS ENord magicolor 3100 User Manual Download Page 139

Internal IDE Hard Disk Drive 

133

1

Turn off the printer, and then 
disconnect the power cord and 
all interface cables from the 
printer.

2

Loosen two screws (one on 
each end of the interface panel) 
and, using the tab on the lower 
side of the panel, pull the 
controller board from 
the printer.

3

Position the controller board on 
a flat surface so the controller board lies flat and the interface panel is 
facing you.

4

Attach the internal IDE 
hard disk drive to the hard 
disk bracket.

Attach the internal IDE 
hard disk drive to the 
bracket with the grooved- 
end of the bracket facing 
the ribbon cable. 

The screw holes in the 
bottom of the hard disk 
should match up with the 
holes on the hard disk 
bracket. 

Fasten the hard disk to the bracket with the screws provided.

5

Position the hard disk so that the four support posts face the controller 
board, the colored stripe on the ribbon cable faces away from you, and 
the connector is down.

6

Insert ribbon cable connector pin 1 (the colored stripe side of the cable) in 
hard disk connector pin 1. 

Attention

Make sure that the ribbon cable connector and the controller board 
connector pins are properly aligned. Damage to the controller board 
could result if the pins are misaligned.

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIII

IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII      IIIIIIIII

ENord- Istedgade 37A - 9000 Aalborg - telefon 96333500

Summary of Contents for ENord magicolor 3100













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands