Microsens MS400870M Series User Manual Download

Page: 18 / 170

command you
would like to
view its current
setting

Config

Enter
Config
mode

While in Enable
mode, enter the

configure

command.

Console(config)#

In Enable mode,
users can access the
Switch‟s advanced
features, such as
VLAN, Rate limit,
QoS, etc.

aggr

When in Config
mode, enter the

aggr

command.

Console(config-
aggr)#

Configure LACP
functions.

cfm

When in Config
mode, enter the

cfm

command.

Console(config-cfm)# Configure the

Managed Switch
OAM 802.1ag CFM
settings.

dot1x

When in Config
mode, enter the

dot1x

command.

Console(config-
dot1x)#

Configure the
Managed Switch to
send information
when 802.1x client
authenticates via the
Switch.

exit

When in Config
mode, enter the

exit

command.

Console#

Exit from current
mode

help

When in Config
mode, enter the

help

command.

Console(config)#

Show available
commands that can
be used in Config
mode.

history

When in Config
mode, enter the

history

command.

Console(config)#

List commands that
have been used.

igmpfilter

When in Config
mode, enter the

igmpfilter

command.

Console(config-
igmpfilter)#

Configure IGMP
filtering settings.

igmp

When in Config
mode, enter the

igmp

command.

Console(config-
igmp)#

Configure IGMP
settings.

mac

When in Config
mode, enter the

mac

command.

Console(config-
mac)#

Set up

each port‟s

MAC learning
function.

mirror

When in Config
mode, enter the

mirror

command.

Console(config-
mirror)#

Set up target port for
mirroring.

mvr

When in Config
mode, enter the

mvr

command.

Console(config-mvr)# Configure Multicast

VLAN Registration
(MVR) settings.

port

When in Config

Console(config)#

Configure the status

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands