Microsens MS400870M Series User Manual Download

Page: 168 / 170

168

Click

to start loading factory settings.

4.6.4 Load Factory Settings Except Network Configuration

Load Factory Settings Except Network Configuration

will set all the configuration of the

Managed Switch back to the factory default settings. However, IP and Gateway addresses
will not restore to the factory default.

Load Factory Settings Except Network Configuration

is very useful when network

administrators need to re-configure the system

“REMOTELY” because conventional Factory

Reset will bring network settings back to default and lose all network connections.

Select

Load Factory Setting Except Network Configuration

from the

System Utility

menu, the following screen page shows up.

Click

to start loading factory settings except network configuration.

4.6.5 Backup Configuration

Select

Backup Configuration

from the

System Utility

menu and then the following screen

page appears.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands