Microsens MS400870M Series User Manual Download

Page: 117 / 170

117

Channel Limit:

Specify the maximum transport multicast stream.

Enable:

To enable each port

‟s

IGMP filtering function. The default setting is

“Off” which is

disabled.

Port:

View-only field that shows the port number that is currently configured.

IPMC Profile:

In IGMP filtering, it only allows information specified in IPMC Profile fields to

pass-through. (The field for IPMC Profile name is from the entry registered in

IPMC Profile

option.)

4.4.12 Static Multicast Configuration

Select the option

Static Multicast Configuration

from the

Switch Management

menu and

then the following screen page appears.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands