Microsens MS400870M Series User Manual Download

Page: 152 / 170

152

In order to view the real-time RSTP statistics status of the Managed Switch, select

RSTP

Statistics

from the

RSTP Monitor

menu and then the following screen page appears.

RSTP Transmitted:

The total transmitted RSTP packets from current port.

STP Transmitted:

The total transmitted STP packets from current port.

TCN Transmitted:

The total transmitted TCN (Topology Change Notification) packets from

current port.

RSTP Received:

The total received RSTP packets from current port.

STP Received:

The total received STP packets from current port.

TCN Received:

The total received TCN packets from current port.

Illegal Received:

The total received illegal packets from current port.

Unknown Received:

The total received unknown packets from current port.

4.5.7 802.1X Monitor

4.5.7.1 80.2.1X Port Status

802.1X Port Status

allows users to view a list of all 802.1x

ports‟ information. Select

802.1X

port status

from the

802.1x Monitor

menu and then the following screen page appears.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands