Microsens MS400870M Series Page 17 User Manual Download

Page: 17 / 170

mode, enter the

history

command.

have been used.

While in Enable
mode, enter the

command.

Console(ip)#

Configure IP
addresses of the
Managed Switch.

logout

While in Enable
mode, enter the

logout

command.

Username:

Logout

ping

While in Enable
mode, enter the

ping

command

and followed by

target

Console#

The ping test from
the Managed Switch
to another network
unit.

reboot

While in Enable
mode, enter the

reboot

command.

Boot-up message

To restart the
Managed Switch.

restore

While in Enable
mode, enter the

restore

command.

Console#

Load factory settings

service

While in Enable
mode, enter the

service

command.

Console(service)#

Configure the
network
management
service.

syslog

While in Enable
mode, enter the

syslog

command.

Console(syslog)#

Configure the Switch
syslog parameters.

system

While in Enable
mode, enter the

system

command.

Console(system)#

Configure the
Managed Switch

‟s

basic information.

time-server

While in Enable
mode, enter the

time-server

command.

Console(time-
server)#

Synchronize the time
of a computer client
or server to another
server.

upgrade

While in Enable
mode, enter the

upgrade

command.

Console(upgrade)#

Upgrade the
Managed Switch

‟s

firmware and restore
the previous settings.

user

While in Enable
mode, enter the

user

command.

Console(user)#

Configure user
accounts.

write

While in Enable
mode, enter the

write

command.

Console#

Save configuration to
the Managed
Switch

‟s flash

memory.

show

While in Enable
mode, enter the

show

command or

enter the

show

command and
followed by

the

Console#

Show a list of
commands or show
the current setting of
each listed
command.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands