manualshive.com logo in svg

Microsens MS400870M Series, User Manual

Share
Download
Microsens MS400870M Series User Manual Download Page 151

 

 

151 

Root ID:

 Display this Managed Switch

‟s Root ID. 

 

Root port:

 Display this Managed Switch

‟s Root Port Number. 

 

4.5.6.2 RSTP Port Status 

 
RSTP  Port  Status 

allows  users to  view  a 

list of all RSTP ports‟ information. Select 

RSTP 

Port Status 

from the 

RSTP Monitor 

menu and then the following screen page appears. 

 

 

 

In this page, you can find the following information of a RSTP port: 
 

Port Number: 

The number of the port. 

 

VLAN ID:

 The VID of the VLAN that this port belongs to. 

 

Path Cost:

 The Path Cost of the port. 

 

Edge  Port:

 

“Yes” is displayed if the port is the Edge port connecting to an end station and 

does not receive BPDU. 
 

P2p Port:

 

“Yes” is displayed if the port link is connected to another STP device. 

 

Protocol:

 Display RSTP or STP. 

 

Role:

 Display the Role of the port (non-STP, forwarding or blocked). 

 

Port State:

 Display the state of the port (non-STP, forwarding or blocked). 

 

4.5.6.3 RSTP Statistics 

 

Summary of Contents for MS400870M Series











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands