Microsens MS400870M Series Page 112 User Manual Download

Page: 112 / 170

112

Query Response Interval:

This determines the maximum amount of time allowed before

sending an IGMP response report. (Default value 100, One Unit=0.1 second)

Fast Leave:

The Fast Leave option may be enabled or disabled. This allows an interface to

be ignored without sending group-specific queries. The default setting is

“Disabled”.

Router Ports:

When ports are connected to the IGMP administrative routers, they should

be set to

“Y”. Otherwise, the default “N” will be applied.

4.4.11.2 IGMP VLANID Configuration

Select the option

IGMP VLAN Configuration

from the

IGMP Snooping

menu and then the

following screen page with the ability information of IGMP Snooping and Querying in
VLAN(s) appears.

Select the current VLAN(s) and click

Edit

to view and edit the ability settings.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands