manualshive.com logo in svg

Microsens MS400870M Series, User Manual, Page: 159 / 170

Share
Download
Microsens MS400870M Series User Manual Download Page 159

 

 

159 

 

 

Update: 

Click 

“Update” to

 

update the DHCP snooping table. 

 

Cli Port: 

View-only field that shows where the DHCP client binding port is. 

 

VID: 

View-only field that shows the VLAN ID of the client port. 

 

CliIP Addr: 

View-only field that shows client IP address. 

 

CliMAC Addr:

 View-only field that shows client MAC address. 

 

SrvIP Addr: 

View-only field that show the server IP address.

 

 

TimeLeft: 

View-only field that shows DHCP client lease time. 

 

4.5.12 CFM Information 

 

Ethernet  Connectivity  Fault  Management  (CFM)  is  an  end-to-end  and  service-to-service 
Ethernet  layer  operations,  administration  and  maintenance  (OAM)  802.1ag  protocol.  It 
includes  practical  connectivity  monitoring,  fault  verification  and  fault  isolation  for  large 
Ethernet metropolitan-area networks (MANs) and WANs.  
As  its  name  implies,  IEEE  802.1ag  focuses  on  the  connectivity  fault  management  which 
provides the following four features on each Virtual Local Area Network (VLAN) basis. 
 

 

Fault Detection/Fault notification 

 

Fault verification 

 

Fault isolation

 

 

Fault Detection/Fault notification 

Summary of Contents for MS400870M Series











































































































































































Reviews:

No comments