manualshive.com logo in svg

Microsens MS400870M Series, User Manual, Page: 131 / 170

Share
Download
Microsens MS400870M Series User Manual Download Page 131

 

 

131 

Linktrace Testing: 

To activate Link Trace route and configuration. 

 

Y.1731 Round-Trip Delay Measurement: 

To activate Link Trace route and configuration. 

 

4.4.15.1 Maintenance Domain 

 

Select the option 

Maintenance Domain Settings 

from the 

CFM Configuration 

menu and 

then the following screen page appears. 
 

 

 

MD  Name:

  View-only  field  that  shows  the  current  CFM  Service  Domain  of  the  Managed 

Switch. 
 

Format:

 View-only field that shows the current Domain type (support string only). 

 

MD Level:

 View-only field that shows the Service Level of Domain. 

 

MHF:

 View-only field that shows the 

“MIP Half Function” or “MEP Half Function”. 

 
Click 

New

  to  register  a  new  Maintenance  Domain  and  then  the  following  screen  page 

appears. 
 
Click 

Edit

 to edit and view Maintenance Domain settings. 

 
Click 

Delete

 to remove a current Maintenance Domain.  

 

Summary of Contents for MS400870M Series











































































































































































Reviews:

No comments