Microsens MS400870M Series Page 64 User Manual Download

Page: 64 / 170

4.3.5 Device Community

Click the option

Device Community

from the

Network Management

menu and then the

following screen page appears.

Up to 10 Device Communities can be set up.

Click

New

to add a new community and then the following screen page appears.

Click

Edit

to view the current community settings.

Click

Delete

to remove a registered community.

Current/Total/Max Agents:

View-only field.

Current:  This shows the number of current registered communities.
Total:  This shows the number of total registered community users.
Max Agents:  This shows the number of maximum number available for registration.
The default maximum number is 10.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands