Microsens MS400870M Series Page 6 User Manual Download

Page: 6 / 170

4.4.11.5 IGMP Filtering ............................................................................................ 116

4.4.12 Static Multicast Configuration ........................................................................... 117

4.4.13 MVR ................................................................................................................. 119

4.4.13.1 MVR Settings ............................................................................................ 120

4.4.13.2 MVR Group ............................................................................................... 122

4.4.14 SKA Configuration ........................................................................................... 123

4.4.14.1 DHCP Option 82 Settings .......................................................................... 124

4.4.14.2 DHCP Port settings ................................................................................... 126

4.4.14.3 Filter Configuration .................................................................................... 126

4.4.14.4 Static IP Table Configuration ..................................................................... 127

4.4.15 CFM Configuration .......................................................................................... 129

4.4.15.1 Maintenance Domain ................................................................................ 131

4.4.15.2 Maintenance Association Settings ............................................................. 133

4.4.15.3 Maintenance End Point List ....................................................................... 135

4.4.15.4 Maintenance End Point Settings ............................................................... 135

4.4.15.5 Loopback Testing ...................................................................................... 137

4.4.15.6 Linktrace Testing ....................................................................................... 138

4.4.15.7 Y.1731 Round-Trip Delay Measurement .................................................... 139

4.4.16 Access Control List Management (ACLM) ...................................................... 139

4.5 Switch Monitor .......................................................................................................... 143

4.5.1 Switch Port State ............................................................................................... 144

4.5.2 Port Traffic Statistics .......................................................................................... 145

4.5.3 Port Packet Error ............................................................................................... 146

4.5.4 Port Packet Analysis Statistics ........................................................................... 147

4.5.5 LACP Monitor .................................................................................................... 148

4.5.5.1 LACP Port Status ........................................................................................ 148

4.5.5.2 LACP Statistics ............................................................................................ 149

4.5.6 RSTP Monitor .................................................................................................... 150

4.5.6.1 RSTP VLAN Bridge Overview ..................................................................... 150

4.5.6.2 RSTP Port Status ........................................................................................ 151

4.5.6.3 RSTP Statistics ........................................................................................... 151

4.5.7 802.1X Monitor .................................................................................................. 152

4.5.7.1 80.2.1X Port Status ..................................................................................... 152

4.5.7.2 802.1X Statistics .......................................................................................... 153

4.5.8 IGMP Snooping Status....................................................................................... 154

4.5.8.1 Snooping Status .......................................................................................... 154

4.5.8.2 IGMP Group Table ....................................................................................... 155

4.5.9 MAC Address Table ........................................................................................... 156

4.5.10 SFP Information ............................................................................................... 156

4.5.10.1 SFP Port Information ................................................................................. 156

4.5.10.2 SFP Port State .......................................................................................... 157

4.5.11 DCHP Snooping ............................................................................................... 158

4.5.12 CFM Information .............................................................................................. 159

4.5.12.1 CFM Stack ................................................................................................. 160

4.5.12.2 CFM Statistics ........................................................................................... 161

4.5.12.3 Maintenance End Point ............................................................................. 162

4.5.12.4 Remote Maintenance End Points .............................................................. 163

4.5.12.5 Linktrace Reply ......................................................................................... 163

4.6 System Utility ........................................................................................................... 164

4.6.1 Event Log .......................................................................................................... 165

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands