Microsens MS400870M Series Page 161 User Manual Download

Page: 161 / 170

161

Select a port from the pull-down menu, then the selected port

‟s CFM stack status will be

displayed.

VLAN ID:

View-only field that shows the VLAN ID of this selected port.

Direction:

View-only field that shows which direction CCMs are sent.

MAC Address:

View-only field that shows the MAC address of this Managed Switch.

Maintenance Domain:

View-only field that shows the MD of the selected port.

Maintenance Association:

View-only field that shows the MA of the selected port.

MD Level:

View-only field that shows the MD level of the selected port.

MEP ID:

View-only field that shows the MEP ID of the selected port.

4.5.12.2 CFM Statistics

Select

CFM Statistics

from the

CFM Information

menu and then the following screen page

appears.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands