Microsens MS400870M Series Page 126 User Manual Download

Page: 126 / 170

126

a. it will receive packets with Agent information and the Managed Switch will

forward them.

b. it will receive packets without Agent information and the Managed Switch will add

Agent information.

When Trust port is set to disabled,

a. it receives packets with Agent information and the Managed Switch will drop

them.

b. it receives packets without Agent information and the Managed Switch will add

Agent information.

4.4.14.2 DHCP Port settings

Select the option

DHCP Port Settings

from the

SKA Configuration

menu and then the

following screen page appears.

Unlimited:

Non-Limited. (Static IP or DHCP assigns IP)

Fixed IP:

Only Static IP. (The Static IP table must be created first.)

DHCP:

DHCP server assigns IP address.

4.4.14.3 Filter Configuration

Select the option

Filter Configuration

from the

SKA Configuration

menu and then the

following screen page appears.

Summary of Contents for MS400870M Series











































































































































































Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands

Microsens MS400870M Series, User Manual

Search results

Summary of Contents for MS400870M Series

Reviews:

Related manuals for MS400870M Series

Brands by name

Popular brands