Microsens MS400870M Series Page 16 User Manual Download | Manualshive

Page: 16 / 170

background image

16

history

command.

logout

While in User
mode, enter

logout

command.

Username:

Logout

ping

While in User
mode, enter the

ping

command

and followed by

target

IP

.

Console>

The ping test from
the Managed Switch
to another network
unit.

show

While in User
mode, enter the

show

command or

enter the

show

command and
followed by

the

command you
would like to
view its current
setting

.

Console>

Show a list of
commands or show
the current setting of
each listed
command.

Enable

Enter
Enable
mode

While in User
mode, enter the
enable command
and a password
(press Enter).

Console#

Enter Enable mode.

backup

While in Enable
mode, enter the

backup

command.

Console(backup)#

Backup configuration
file via FTP or TFTP.

cfm

While in Enable
mode, enter the

cfm

command.

Console(cfm)#

Run loopback
linktrace and delay
measurement test.

configure

While in Enable
mode, enter the

configure

command.

Console(config)#

Enter Config mode.

Console

While in Enable
mode, enter the

Console

command.

Console(Console)#

Set up time-out timer
when the user is
inactive.

disable

While in Enable
mode, enter the

disable

command.

Console>

Exit from current
mode.

exit

While in Enable
mode, enter the

exit

command.

Console>

Exit from current
mode.

help

While in Enable
mode, enter the

help

command.

Console#

Show available
commands that can
be used in Enable
mode.

history

While in Enable

Console#

List commands that

«
...
14
15
16
17
18
...
»

Summary of Contents for MS400870M Series











































































































































































Reviews:

No comments

Related manuals for MS400870M Series

Brand: D-Box Pages: 27

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brand: Hama Pages: 18

uRage Vendetta 210

Brand: Hama Pages: 36

Brand: IBM Pages: 164

8265 Nways ATM Switch

Brand: IBM Pages: 174

Brand: Kathrein Pages: 41

IO-Link BNI LH1-303-S11-K091

Brand: Balluff Pages: 12

RMQ-Titan M30 Series

Brand: Eaton Pages: 4

Brand: GE Pages: 2

Brand: PKP Pages: 11

Brand: Vega Pages: 36

AMX ENOVA DVX-3250HD-SP

Brand: Harman Pages: 119

USB 2.0 7-Port Hub HO97916

Brand: GE Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands