Metrix DOX3104 User Manual Download Page 98

Page: 98 / 193

Functional Description

4-Channel SPO Digital Oscilloscopes

Functional Description

VII - SAVE/RECALL System

(cont‟d)

Restoring the
«Factory Settings»

(Default Setup)

Press the «

Default

» button to restore the « Default Setup » :

Display obtained after
restoring the « default

setup »:

Channel CH1

Sensitivity: 1V/div,

Probe factor: 1X,

Impedance:

1MΩ,

Coupling: DC, BW

Limit : Full Time Base:

1µs/div

Restoring
Waveforms

Waveform files must be saved in external memory (USB memory device).

To restore a waveform plug first the USB device in the « USB host »
connector of the oscilloscope front panel

1°

Plug the USB memory device in the «USB host» connector and wait for the

USB device icon

and the Popup message

« USB Flash Drive Plugged

in”

2°

Press the

« Save/Recall »

button to open the SAVE/RECALL menu

3°

Press the «

type

» button and select

Waveforms

4°

Press the «

Recall »

button and wait for the contents of the « USB memory

device » is displayed on the screen

5°

Use the

Universal

knob to select the waveform file

« .DAV »

to be displayed

on the screen

6°

Press the

« Load

» button to restore the selected waveform file

7°

Wait until the selected waveform is displayed on the screen

Notes :

1°

When the saved waveform is displayed the acquisition stops

The displayed

values of the time base coefficient, the sampling rate, and the memory depth
correspond to the restored waveform. To refresh the display of vertical

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 98 / 193

Search results

Summary of Contents for DOX3104

Reviews: