Metrix DOX3104 User Manual Download Page 37 | Manualshive

Page: 37 / 193

Metrix DOX3104 User Manual Download Page 37

Functional Description

4-Channel SPO Digital Oscilloscopes

37

Operation Steps

To display in details a portion of the waveform:

1. Press the "

Horiz

" button to open the HORIZONTAL menu.

2. Turn the "

S/div

" knob to adjust the main timebase.

3. Press the «

Zoom

» button to activate the horizontal Zoom.

4. Turn the «

S/div

» knob to adjust the

“Zoom” time base.

5. Turn the horizontal "

Position

" knob to move the zoom window.

In the example below, we display in « Zoom » mode, a detail (a 0.24µs wide
window with a resolution of 0.5ns situated at 235µs from the trig event) of a signal
acquired at 2GSPS sample rate with a memory depth of 28Mpoints. The
oscilloscope has recorded the evolution of the signal during a lapse of time of 14ms
with an elementary time step of 0.5ns :
The arrows indicates the delay value (Delay=235µs) relative to the trigger event
and the signal value for this delay :

We can « Stop » the trace refresh («

Run/Stop

» button) to observe it in detail.

For example we can determine the value that the signal has 74ns before the trigger
event by moving the zoomed window (Horizontal « Position » knob):
The red arrows indicate the value of the signal at the trigger event and 74ns before :

«
...
35
36
37
38
39
...
»

Summary of Contents for DOX3104


































































































































































































Reviews:

No comments