Metrix DOX3104 User Manual Download Page 71

Page: 71 / 193

Functional Description

4-Channel SPO Digital Oscilloscopes

Functional Description

IV - ACQUISITION System

(cont‟d)

RUN/STOP

SINGLE

AUTO

NORMAL

Run/Stop

Press the

"Run/Stop"

button to start (Run/Stop button is lit in yellow) the

signal acquisition, press this button again to Stop (Run/Stop button is lit in
red).

Single

Press the

″Single″

button to

Arm

the trigger

(

the oscilloscope is

Ready,

and

the “Run/Stop” button is lit in yellow

)

, then when a trigger event is detected a

unique acquisition starts, when the acquisition is completed the oscilloscope
Stops (Run/Stop button is lit in red).

SINGLE

mode when you press the

"Single"

button to start

a unique

acquisition, the oscilloscope performs the following steps:

1. Acquisition of

“Pre-Trigger” samples, which are represented on the screen

by the portion of the waveform to the left of the Trigger point.

2. The oscilloscope acquires the « Pre-Trigger » samples continously and

waits for the trigger event.

3. Detection of the trigger event.

4. After the trigger event, the acquistion continues until the recording memory

is filled with the « Post-Trig » samples, which are represented on the screen
by the portion of the waveform to the right of the trigger point

5. The oscilloscope displays the waveform and Stops (Run/Stop button is lit in

red). Press again the

« Single

» button to start a new single acquisition .

Auto

Press the «

Auto

» button to enable the

Auto

mode. In this mode, acquisitions

occur in the presence or absence of a trigger event.

Normal

Press the «

Normal

» button to enable the « Normal » mode.

In this mode, acquisitions occur only when a trigger event is detected.

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 71 / 193

Search results

Summary of Contents for DOX3104

Reviews: