Metrix DOX3104 User Manual Download Page 17 | Manualshive

Page: 17 / 193

Metrix DOX3104 User Manual Download Page 17

Functional Description

4-Channel SPO Digital Oscilloscopes

17

Functional Description

AUTO SETUP

Auto Setup

«

Auto Setup

» button on « RUN CONTROL

” block

DOX3000 digital oscilloscopes have an « Auto Setup » function that
configures automatically the device to produce a display adapted to the
signals at the channel inputs.

After launching an “Auto Setup”, select, if necessary, the type of signal
displayed among the four proposed : Several periods, One period, Rising or
Falling edge at the center of the screen.

Auto Setup

Function

Option

Description

Multi-cycle

Autoset

and displays several cycle signal.

Single-cycle

Autoset

and displays single cycle signal.

Rising edge

Autoset

and displays the Rising edge.

Falling edge

Autoset

and displays the Falling edge.

Undo config.

The oscilloscope recalls the previous
Setup.

The “Auto Setup” sets the trigger source and displays the channels according
to the following criteria :

●

If multiple channels have an input signal, channel with the lowest frequency

signal has the priority.

●

If no channel is « On » and no signal is found, no channels are displayed.

●

If one or more channels are « On » and no signal is found, only the « On »

channels remains active.

«
...
15
16
17
18
19
...
»

Summary of Contents for DOX3104


































































































































































































Reviews:

No comments