Metrix DOX3104 User Manual Download Page 40

Page: 40 / 193

Functional Description

4-Channel SPO Digital Oscilloscopes

Functional Description

III - TRIGGER

System (cont’d)

1. Edge

Trigger
« Edge »

Option

Settings

Description

Type

Edge

The rising or falling edge of the signal source is used to
trigger.

Source

CH1 CH2 CH3 CH4

Note : The trigger source is active even if the channel is
off

EXT

The EXT TRIG source signal is not displayed. The EXT
source is the signal

to the “EXT TRIG” input BNC in the back

of the oscilloscope. The trigger level adjustement range is: -
1,6V to +1,6V

EXT/5

Same as EXT option, but the signal is attenuated by a factor
of 5. The trigger level range is multiplied by 5 : -8V to +8V

AC line

The trigger source signal is the AC line. The trigger coupling
is set to « DC » and the trigger level to 0V.

Slope

Trigger on the rising edge of the source signal.

Trigger on the falling edge of the source signal.
Trigger on the rising and falling edges of the source signal.

Holdoff

Adjustable
Fixed

Use the « Universal » knob to adjust the « holdoff ».
The « holdoff » is fixed to the latest set value

Coupling

All components of the signal source passes

Blocks the DC component and attenuates the AC signal
below 5.8Hz.

Low Pass

Filter

HF reject

Attenuates «

high frequency »

components above

1.27MHz.

High Pass

Filter

LF
reject

Blocks the DC component and attenuates the «

low

frequency »

components below 2.08MHz.

Noise
Reject

On Off

Enable or Disable the Noise Reject

Operation Steps

1. Set the trigger type

Press the “

Setup

» button to open the TRIGGER menu.

2) Press the "

Type

" button and select "

Edge

2. Set the trigger Source

Press the "

Source

" button and select the trigger source: "CH1", "CH2", "CH3", "CH4", "EXT",

"EXT/5" or "AC Line".

3. Set the trigger slope

Press the « Slope

» button and select the trigger slope “

”, “

” or “

”.

4. Set the Holdoff

Press the «

Holdoff close

» button



Holdoff time

» and use the “Universal” knob to adjust

the « Holdoff » time.

5. Set the Trigger coupling

a. Press the

“Set Up”

button to open the trigger settings menu.

Press the

“Coupling”

button and select the coupling type: “DC”, “AC”, “HF Reject” ou “LF

Reject”.

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 40 / 193

Search results

Summary of Contents for DOX3104

Reviews: