Metrix DOX3104 User Manual Download Page 14

Page: 14 / 193

Getting started

4-Channel SPO Digital Oscilloscopes

Getting started

Verification of
instrument
operation

To check the operation of the oscilloscope, perform the following steps:

Steps

1. Turn on the oscilloscope.

Press the

« Default »

button

of the « RUN CONTROL » pad to load the

« default » configuration of the oscilloscope. Note : The default value for the
attenuation compensation coefficient of the probe is 1X

2. Switch the attenuation of the

“probe” to the « 1X » position, plug it on CH1

and turn clockwise to block. Connect the probe tip and the ground alligator clip
to the terminals

“Cal 3V 1kHz” and “Ground” of the probe adjust output.

3. Press the "

Auto Setup

" button to display the

“3Vpp, 1kHz” Cal square wave.

4. Press the

"CH1"

button to disable CH1. Then press the "

CH2"

button to

enable

CH2 and repeat steps 2 and 3 to display the Cal signal on CH2

Repeat the previous steps with the channels CH3 and CH4

Cal Output : 3V 1kHz

GND

CH1 channel

Default Setup

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 14 / 193

Search results

Summary of Contents for DOX3104

Reviews: