Metrix DOX3104 User Manual Download Page 78 | Manualshive

Page: 78 / 193

Metrix DOX3104 User Manual Download Page 78

Functional Description

78

4-Channel SPO Digital Oscilloscopes

Functional Description

VI - MEASURE Sytem

(cont‟d)

Examples :

Use of X and Y

cursors to measure

the period (or

frequency) and the

amplitude of a sine

wave

When the «

Manual Cursors

» are active, the display shows two horizontal or

vertical parallel cursors to measure voltage (Y cursors) or time (X cursors). Use
the "Universal" knob to move the cursors. Select the appropriated reference
source for cursors measurements.

●

Voltage cursor (Y cursors) :

The voltage cursors materialized on the screen

in the form of horizontal lines. The cursor position is in Volt.

●

Time Cursor (X cursors) :

The time cursors materialized on the screen in

the form of vertical lines. The cursor position is in second.

●

Moving the cursors :

Select the cursor (X or Y) and

use the

"Universal"

knob to move it. When you move the cursor the value corresponding to the
vertical and(or) horizontal position of the cursor is displayed in the top left of
the screen.

«
...
76
77
78
79
80
...
»

Summary of Contents for DOX3104


































































































































































































Reviews:

No comments