Metrix DOX3104 User Manual Download Page 178

Page: 178 / 193

Messages

178

4-Channel SPO Digital Oscilloscopes

Messages / Help

« Help »

The oscilloscope has an embedded help function that supplies multi-language Help
information (

English

French

German

). To access help:

Press the front panel "

Help

" button to activate the help, then press every button to display

the corresponding help information.

Note : To display the help information corresponding to the « Single » or

« Run/Stop» buttons, press these buttons immediately after you press the

« Help » button. Otherwise the « Single » button is used to display the next

page of the displayed help and the

“Run/Stop” button the previous page,

when the help information exceeds one page.

All submenus of every main menus have their own help information.
Note : If you want to display help information of next page submenus, first press the
«

Help

» button to exit the help status and switch to next page menu then press the

Help

» button to enter the help status again and press the submenu option buttons to

display the corresponding help information.

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 178 / 193

Search results

Summary of Contents for DOX3104

Reviews: