Metrix DOX3104 User Manual Download Page 136

Page: 136 / 193

Functional Description

136

4-Channel SPO Digital Oscilloscopes

X - DECODE SPI Serial Bus Decode

SPI Serial Bus

Setting up the oscilloscope to capture SPI bus signals

To analyse the SPI bus (Serial Peripheral Interface), we need to connect the inputs of the
oscilloscope to the following SPI signals :

Clock - MOSI data - MISO data - Framing

And to set for each signal the logic threshold that defines the « Low » and « High » levels.

Setting up the oscilloscope to capture and analyse the SPI bus signals:

1° Press the front panel «

Decode

» button to open the DECODE menu

2° Press the «

Serial

» button and select

“Serial 1” or “Serial 2”

3° Press the «

Decode

» button and use the «

Universal

» knob to select «

SPI

Note : The default value are

“I2C” for Serial 1 and “SPI” for Serial 2.

4° Press the «

Signal

» button to open the SPI « SIGNAL » submenu

5° Press the «

CLK

» button to open the SPI

“CLK” submenu

a) Press the «

CLK

» button and use the « Universal » knob to assign a channel to the

SPI « CLK » signal

b) Press the «

Threshold

» button and use the « Universal » knob to set the threshold

value.

c) Press the «

Edge »

button to set the rising or the falling edge, the selected edge is

used by the oscilloscope to «

latch

» the serial data.

6° Press the «

» button to return to SPI

“SIGNAL” submenu

7° Press the «

MISO

» button to open the

“MISO” submenu

a) Press the «

MISO

» button and use the « Universal » knob to assign a channel to the

MISO signal

b) Press the «

Threshold

» button and use the Universal knob to set the threshold

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 136 / 193

Search results

Summary of Contents for DOX3104

Reviews: