Metrix DOX3104 User Manual Download Page 10

Page: 10 / 193

Instrument Description

4-Channel SPO Digital Oscilloscopes

Instrument

Description (cont’d)

User
display
interface

Trigger

status:

Arm:

The oscilloscope is acquiring pre-trigger data. All triggers are ignored in this state.

Ready:

All pre-trigger data has been acquired and the oscilloscope is ready to accept a trigger event.

Trig’d:

The oscilloscope has detected a trigger event and is acquiring the post-trigger data.

Stop:

The oscilloscope has stopped acquiring waveform data.

Auto

: In trigger « Auto » mode, the oscilloscope refreshes the trace even in absence of a trigger event

Time Base coefficient : S/div.

Indicates the horizontal trigger position relative to the screen center, use the horizontal Position knob to
adjust it.

“Zoom” Time Base coefficient : S/div

Awg : High-Z

Arbitrary waveform Generator output impedance: High-Z or 50

Ω

USB flash plugged-in

Indicates whether the back USB option is set to : Computer or Printer

“back USB ”

option is set to

“

Computer

”

“back USB”

option is set to

“

Printer

”

Shows the Channel vertical position symbol

Shows the CHi active Menu (CH 1)

10.

Input Coupling symbol

11.

Indicates whether the bandwidth limit is « 20MHz » or « Full Bandwidth».

12.

Vertical Scale Adjust : « Coarse » or « Fine »

13.

Probe Factor Selection :

.1X .2X .5X 10X 20X 50X 100X 200X 500X 1000X 2000X 5000X 10000X

14.

Input impedance : 1M

Ω - 50Ω

15.

Next page Menu CHi (CANAL i)

16.

Display for each of the active channels:
Channel number, Probe factor, Input Impedance, « B » for the 20MHz bandwidth limit if enabled, Input
Coupling, Vertical Sensitivity V/div

17.

Indicates the trigger type, the trigger source, the trigger slope, the trigger coupling and the trigger level
in Volt.

18.

Indicates the sample rate and the current memory depth.

19.

Indicates the frequency of the trigger source signal (hardware counter)

1 2 3 4 5 6 7

19

18

17

16

20

10 11 12 13 14 15

Summary of Contents for DOX3104


































































































































































































Search results

Summary of Contents for DOX3104

Reviews:

Metrix DOX3104, User Manual, Page: 10 / 193

Search results

Summary of Contents for DOX3104

Reviews: