Mercury Racing HP1200 SCi Dry Sump Operation, Maintenance & Warranty Manual Download Page 5

Page: 5 / 106

TABLE OF CONTENTS

Warranty Information

Warranty Coverage......................................................................1

General Information

Identification Record....................................................................2

Boater's Responsibilities..............................................................3

Boat Horsepower Capacity..........................................................4

High‑Speed and High‑Performance Boat Operation...................4

Lanyard Stop Switch....................................................................5

Protecting People In The Water...................................................6

Exhaust Emissions......................................................................7

Wave And Wake Jumping...........................................................9

Impact With Underwater Hazards..............................................10

Trailering Boat........................................................................... 11

Safe Boating Suggestions......................................................... 11

Stolen Power Package.............................................................. 14

Specifications

Fuel Requirements (HP1200 SCi).............................................15

Crankcase Oil............................................................................17

Capacities..................................................................................18

General Engine Specifications (HP1200 SCi)........................... 19

Engine Operating Limitations (HP1200 SCi)............................. 20

California Emissions Regulations..............................................20

Engine Break‑in.........................................................................21

After Break‑In Period.................................................................21

Operation

Instrumentation..........................................................................22

Warning System........................................................................ 22

Electrical System Overload Protection...................................... 24

Remote Controls (Console Mounted Zero Effort)......................27

Power Trim................................................................................ 28

Summary of Contents for HP1200 SCi Dry Sump











































































































Search results

Summary of Contents for HP1200 SCi Dry Sump

Reviews:

Related manuals for HP1200 SCi Dry Sump

Brands by name

Popular brands

Mercury Racing HP1200 SCi Dry Sump, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP1200 SCi Dry Sump

Reviews:

Related manuals for HP1200 SCi Dry Sump

Brands by name

Popular brands