Mercury Racing HP1200 SCi Dry Sump Operation, Maintenance & Warranty Manual Download Page 66

Page: 66 / 106

MAINTENANCE

6. Start the engine and let it run for at least two minutes at idle,

shifting the transmission from forward to reverse several

times.

7. Stop the engine and check the transmission oil level with the

dipstick. If addition oil is required, add it through the dipstick

tube to bring the level up to the "FULL" mark.

FULL

6790

a -

Dipstick

b -

"FULL" mark

c -

Dipstick tube

Tube Ref No.

Description

Where Used

Part No.

Type F or FA

Transmission Fluid

Transmission

Obtain

Locally

CHANGING DRIVE UNIT OIL (DRY SUMP)

IMPORTANT: Fill the dry sump drive and transom input shaft

housing with TORCO MTF Gear Lube.

Summary of Contents for HP1200 SCi Dry Sump











































































































Search results

Summary of Contents for HP1200 SCi Dry Sump

Reviews:

Related manuals for HP1200 SCi Dry Sump

Brands by name

Popular brands

Mercury Racing HP1200 SCi Dry Sump, Operation, Maintenance & Warranty Manual

Search results

Summary of Contents for HP1200 SCi Dry Sump

Reviews:

Related manuals for HP1200 SCi Dry Sump

Brands by name

Popular brands