MTHTrains Rail King RS-1 Operator'S Manual Download | Manualshive

Page: 1 / 20

background image

Rail King RS-1 Diesel Engine

OPERATOR’S MANUAL

(3V PS-2)

Compatibility

This engine will operate on any
traditional O-31 Gauge track system,
including M.T.H.’s RealTrax® or
ScaleTrax™ or traditional tubular
track. It is also compatible with most
standard AC transformers. (See page
19 for a complete list of compatible
transformers and wiring instructions.)

PLEASE READ BEFORE USE AND SAVE

Freight Yard Sound

Passenger Station Announcement

1
2
3
...
»

Summary of Contents for Rail King RS-1





















Reviews:

No comments

Related manuals for Rail King RS-1

Brand: Eaton Pages: 32

VLT OneGearDrive

Brand: Danfoss Pages: 44

VLT OneGearDrive

Brand: Danfoss Pages: 21

Brand: Danfoss Pages: 20

Yanmar 3TVN 88C-KHW

Brand: HAKO Pages: 36

Brand: Wood-mizer Pages: 36

Brand: Bison Pages: 19

Brand: cemp Pages: 18

Brand: Baumr-AG Pages: 25

TWINMOT T2-PLUS H

Brand: Germany Motions Pages: 12

Brand: Honda Pages: 59

ClearPath-SCHP Series

Brand: Teknic Pages: 117

ZAtop SM250.100C

Brand: ZIEHL-ABEGG Pages: 16

PowerMax Series

Brand: Seamax Pages: 12

Brand: TAARKS Pages: 9

Brand: Mitsubishi Pages: 24

Brand: Traxxas Pages: 40

Brand: YARDMAX Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands