TJERNLUND SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198 Installation Instructions Manual Download | Manualshive

Page: 1 / 14

background image

Copyright © 1998, Tjernlund Products, Inc. All rights reserved

P/N 8504075

OWNER INSTRUCTIONS, DO NOT DESTROY

Recognize this symbol as an indication of important safety information!

NOTE: MAXIMUM FLUE GAS TEMPERATURES MUST NOT EXCEED 650oF.

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED, LICENSED SERVICE
PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND OPERATION OF THIS
UNIT. READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING INSTALLA-
TION OR OPERATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
IMPROPER INSTALLATION, ADJUSTMENT, SERVICE OR MAINTENANCE POSSIBLY
RESULTING IN FIRE, ELECTRICAL SHOCK, CARBON MONOXIDE POISONING, EXPLO-
SION, PERSONAL INJURY OR PROPERTY DAMAGE.

!

DO NOT DESTROY. PLEASE READ CAREFULLY AND

KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

MODEL SS2G

INSTALLATION INSTRUCTIONS

REV. 1 11/98

56826

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794
PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547
Visit our web site • www.tjernlund.com

1
2
3
...
»

Summary of Contents for SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198















Reviews:

No comments

Related manuals for SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198

Brand: VEM Pages: 16

Brand: Briggs & Stratton Pages: 6

Brand: Sole Diesel Pages: 40

Brand: AL-KO Pages: 144

Brand: DIMOEL Pages: 8

RolloTube S-line Sun DuoFern

Brand: RADEMACHER Pages: 2

Brand: DLE Pages: 4

Brand: DLE Pages: 4

Brand: DANA Pages: 3

MAX-37SZ-H RING

Brand: O.S. engine Pages: 4

Brand: O.S. engine Pages: 17

Brand: O.S. engine Pages: 22

MAX-12TR Series

Brand: O.S. engine Pages: 30

Brand: O.S. engine Pages: 34

Brand: O.S. engine Pages: 21

Brand: Agrimate Pages: 32

Brand: LinMot Pages: 44

Brand: Briggs & Stratton Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands