manualshive.com logo in svg

TJERNLUND SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198, Installation Instructions Manual

Share
Download
TJERNLUND SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198 Installation Instructions Manual Download Page 14

13

MAINTENANCE

INSTALLER AND USER REQUIREMENTS

A vent system inspection must be performed annually by a qualified service agency.  The inspection should include the operation
circuit check, safety interlock test, combustion air test and a  visual  inspection of the complete vent system for corrosion, blockage
or leaks.  Any corrosion, blockage or leaks detected must be repaired or replaced immediately.

MOTOR OILING 

The SS2G Motor has sealed ball bearings and requires no oiling.

HOW TO OBTAIN SERVICE ASSISTANCE

1.  If you have any questions about your Power Venter or if it requires adjustment, repair or routine maintenance, we suggest 

that you contact your installer, contractor or service agency.

2.  If you require technical information contact Tjernlund Products, Inc. at 1-800-255-4208.

When contacting Tjernlund Products, Inc., please have the following information available:

1.  Model of the Power Venter as shown on the label attached to Power Venter.
2.  Name and address of installer and any service agency who performed work on Power Venter.
3.  Date of original installation and dates any service work was performed.
4.  Details of the problem as you can best describe them.

LIMITED PARTS WARRANTY AND CLAIM PROCEDURE

Tjernlund Products, Inc. warrants the components of the SideShot for two years from date of installation.  This warranty covers
defects in material and workmanship.  This warranty does not cover normal maintenance, transportation or installation charges  for
replacement parts or any other service calls or repairs.  This warranty DOES NOT cover the complete SS2G if it is operative,
except for the defective part.

Tjernlund Products, Inc. will issue credit or provide a free part to replace one that becomes defective during the two year warranty
period.  If the part is over 30 months old, proof of date of the installation in the form of the contractor sales/installation receipt is
necessary to prove the unit has been in service for under two years.  All receipts should include the date code of the SideShot to
ensure that the defective component corresponds with the complete unit.  This will help preclude possible credit refusal.

1.) Follow troubleshooting guide to determine defective component.  If unable to determine faulty component, contact your 

Tjernlund distributor or Tjernlund Products Technical Customer Service Department  at 1-800-255-4208 for troubleshooting 
assistance.

2.) After the faulty component is determined, return it to your Tjernlund distributor for replacement.  Please include SideShot date 

code component was taken from.  The date code is located on the Electrical Box coverplate.  If the date code is older than 30 
months you will need to provide a copy of the original installation receipt to your distributor.  Credit or replacement will only be 
issued to a Tjernlund distributor after the defective part has been returned prepaid to Tjernlund.

WHAT IS NOT COVERED

Product installed contrary to our installation instructions
Product that has been altered, neglected or misused
Product that has been wired incorrectly
Product that has been damaged by a malfunctioning or mistuned burner
Any freight charges related to the return of the defective part
Any labor charges related to evaluating and replacing the defective part

REPLACEMENT PARTS

Component

Part Number

Motor  

950-0015

Proving Switch

950-0016

Relay/Timer (approx. 45 second nonadjustable delay)

950-0014

Relay/Timer ( 1 to 10 minute adjustable delay)

950-1067      

Impeller 

950-0008

High Limit Switch

950-0018

Venter Housing

950-0009

Cooling Fan

950-0020

TJERNLUND LIMITED TWO  YEAR WARRANTY

Tjernlund Products, Inc. warrants to the original purchaser of this product that the product will be free from defects due to faulty material or workmanship for a period of (2) years from the date of
original purchase or delivery to the original purchaser, whichever is earlier.  Remedies under this warranty are limited to repairing or replacing, at our option, any product which shall, within the
above stated warranty period, be returned to Tjernlund Products, Inc. at the address listed below, postage prepaid.  THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF, AND TJERNLUND PRODUCTS, INC. EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OF THIS PRODUCT.  THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES AND NO AGENT IS AUTHORIZED TO ASSUME FOR US ANY LIABILITY ADDI -
TIONAL TO THOSE SET FORTH IN THIS LIMITED WARRANTY.  IMPLIED WARRANTIES ARE LIMITED TO THE STATED DURATION OF THIS LIMITED WARRANTY.  Some states do not
allow limitation on how long an implied warranty lasts, so that limitation may not apply to you.  In addition, some states do not allow the exclusion or limitation of incidental or consequential dam -
ages, so that above limitation or exclusion may not apply to you.  This warranty gives you specific legal rights and you may also have other rights which may vary from State to State.  Send all
inquiries regarding warranty work to Tjernlund Products, Inc. 1601 9th Street, White Bear Lake, MN 55110-6794.  Phone (651) 426-2993 • (800) 255-4208 • Fax (651) 426-9547.

Summary of Contents for SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198















Reviews:

No comments

Brands by name

Popular brands

Load more brands