MerCruiser Axius 496 MAG H.O. Owner'S Manual Download

Page: 144 / 148

Section 7 - Troubleshooting

Page 136

90-899883154 JANUARY 2008

Symptom

Remedy

The steering wheel turned past

end stop.

Key off and key on to restore steering wheel self‑centering, cruise control,

and to eliminate the fault code.

Power Trim Does Not Operate (Motor Does Not Operate)

Possible Cause

Remedy

Blown fuse.

Replace fuse. Fuses may be located near the dash

trim switch, at the trim pump, in the positive (red)

power trim battery lead near the battery switch, or a

combination of these.

Loose or dirty electrical connections or damaged

wiring.

Check all associated electrical connections and wires

(especially battery cables). Clean and tighten faulty

connection. Repair or replace wiring.

Power Trim Does Not Operate (Motor Operates but Sterndrive Unit Does Not Move)

Possible Cause

Remedy

Trim pump oil level low.

Fill pump with oil.

Drive unit binding in gimbal ring.

Check for obstruction.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands