MerCruiser Axius 496 MAG H.O. Owner'S Manual Download Page 137

Page: 137 / 148

Section 6 - Storage

90-899883154 JANUARY 2008

Page 129

1. Insert a small wire repeatedly to make sure that vent holes, water drain holes, and

passages are unobstructed and open.

6146

Sterndrive Water Drain Holes

a -

Speedometer pitot tube

b -

Trim tab cavity vent hole

c -

Trim tab cavity drain passage

d -

Gear housing water drain hole (1

each ‑ port and starboard)

e -

Gear housing cavity vent hole

f -

Gear housing cavity drain hole

NOTICE

The universal joint bellows may develop a set when stored in a raised or up position,

causing the bellows to fail when returned to service and allowing water to enter the boat.

Store the sterndrive in the full down position.

2. Lower the sterndrive unit to the full down/in position.
3. For additional assurance against freezing and rust, after draining, fill the cooling system

with propylene glycol mixed to the manufacturer's recommendation to protect engine

to the lowest temperature to which it will be exposed during freezing temperatures or

extended storage

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers instructions, be used in the seawater section of the cooling system for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Battery Storage

Whenever the battery will be stored for an extended period of time, be sure the cells are

full of water and the battery is fully charged and in good operating condition. It should be

clean and free of leaks. Follow the battery manufacturer's instructions for storage.

Power Package Recommissioning

1. Ensure that all cooling system hoses are connected properly and hose clamps are tight.

CAUTION

Disconnecting or connecting the battery cables in the incorrect order can cause injury

from electrical shock or can damage the electrical system. Always disconnect the

negative (‑) battery cable first and connect it last.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands