MerCruiser Axius 496 MAG H.O. Owner'S Manual Download Page 102

Page: 102 / 148

Section 5 - Maintenance

Page 94

90-899883154 JANUARY 2008

Serpentine Drive Belt

WARNING

Inspecting the belts with the engine running may cause serious injury or death. Turn off

the engine and remove the ignition key before adjusting tension or inspecting belts.

33539

Belt Routing Diagram

a -

Idler pulley

b -

Water circulating pump pulley

c -

Alternator pulley

d -

Idler pulley

e -

Power steering pump pulley

f -

Idler pulley

g -

Crankshaft pulley

h -

Seawater pump pulley

i -

Tensioner pulley

Checking

1. Inspect the drive belt for proper tension and for the following:

•

Excessive wear

•

Cracks

NOTE: Minor, transverse cracks (across the belt width) may be acceptable. Longitudinal

cracks (in the direction of belt length) that join transverse cracks are NOT acceptable.

•

Fraying

•

Glazed surfaces

•

Proper tension ‑ 13 mm (1/2 in.) deflection, with moderate thumb pressure, on the

belt at the location that has the longest distance between two pulleys.

mc75130-1

Replacing

IMPORTANT: If a belt is to be reused, it should be installed in the same direction of rotation

as before.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands