MerCruiser Axius 496 MAG H.O. Owner'S Manual Download

Page: 16 / 148

Section 1 - Warranty

Page 8

90-899883154 JANUARY 2008

This limited warranty does not cover the following:

•

Electrical system corrosion

•

Corrosion resulting from damage

•

Corrosion that causes purely cosmetic damage

•

Abuse or improper service

•

Corrosion to accessories, instruments, and steering systems

•

Corrosion to a factory‑installed jet drive unit

•

Damage due to marine growth

•

Replacement parts (parts purchased by the customer)

•

Product sold with less than a one‑year limited product warranty

•

Products used in a commercial application. Commercial use is defined as any work or employment

related use of the product, or any use of the product which generates income, for any part of warranty

period, even if the product is only occasionally used for such purposes.

Global Warranty Charts

IMPORTANT: Please refer to

www.mercurymarine.com/global_warranty

for the most

currant Global Warranty Charts.

Consumer Application Warranty Chart

Consumer Application: Standard Factory Limited Warranty by Region & Boat Brand

Limited Corrosion

Warranty

Non-Certified Boat Brand

Certified Boat Brand

All Boat Brands

Region

Standard SeaCore

Vazer and

Models

with

Closed

Cooling

Scorpion

377

Standard SeaCore

Vazer and

Models

with

Closed

Cooling

Scorpion

377

Vazer,

Standard

Models,

and and

Models

with

Closed

Cooling

SeaCore

USA and
Canada

1 year

3 years

2 years

4 years

3 years

4 years

Latin
America

1 year

3 years

1 year

2 years

4 years

2 years

3 years

4 years

Mexico

1 year

3 years

1 year

4 years

1 year

4 years

Europe

2 years

3 years

2 years

3 years

4 years

3 years

4 years

Japan

1 year

Australia
and New
Zealand

2 years

3 years

3 years all

Tow

Sports

2 years

3 years

3 years all

Tow

Sports

3 years

4 years

South
Pacific

1 year

3 years

1 year

3 years

1 year

3 years

4 years

Asia
(excluding
Japan,
South
Pacific,
Australia,
New
Zealand)

2 years

3 years all

Tow

Sports

2 years

3 years all

Tow

Sports

2 years

NOTE: In regions where the Certified Boat Builder program is not applicable, the regular warranty always applies.
NOTE: In regions where TBD (To Be Determined) is listed, check with your local dealer for warranty length and conditions.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands