MerCruiser Axius 496 MAG H.O. Owner'S Manual Download Page 134

Page: 134 / 148

Section 6 - Storage

Page 126

90-899883154 JANUARY 2008

6. Pump air into the system until both green indicators extend and water drains from both

sides of the engine. The port side will begin draining before the starboard side.

8294

a -

Actuator fitting

b -

Green indicators

c -

Manual release valve

7. Verify that water is draining from each opening. If not, use the

Manual Drain System

instructions.

17254

a -

Port side drain location

b -

Starboard side drain location

8. Allow the system to drain for a minimum of five minutes. Pump air as necessary to keep

the green indicators extended.

9. For DTS engines, pull the lanyard stop switch (if equipped), or disable the ignition circuit

by pulling the fuse marked "CD".

10. Crank the engine over slightly with starter motor to purge any water trapped in the

seawater pump. Do not allow engine to start.

11. Remove the air pump from the air manifold and return it to the mounting bracket.
12. Mercury MerCruiser recommends leaving the drain system open while transporting the

boat or while performing other maintenance. This helps ensure that all water is drained.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands