MerCruiser Axius 496 MAG H.O. Owner'S Manual Download Page 97

Page: 97 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 89

Tube Ref. No.

Description

Where Used

Part No.

Synthetic Blend MerCruiser Engine

Oil SAE25W‑40

Shift cable pivot points & guide

contact surfaces

92‑883725K01

Sterndrive Unit and Transom Assembly

1. Lubricate gimbal bearing by applying approximately 8‑10 pumps of grease from a

typical hand‑operated grease gun.

mc77068-1

a -

Gimbal bearing grease fitting

Tube Ref No.

Description

Where Used

Part No.

U-joint and Gimbal Bearing

Grease

Gimbal bearing

92-802870A1

2. For propeller shaft lubrication, refer to

Propellers

Sterndrive U‑joint Shaft Splines And O‑rings (Sterndrive Unit Removed)

1. Coat sterndrive U‑joint O‑rings and driveshaft splines with grease.

8591

a -

Driveshaft splines

b -

U‑joint O‑rings (3)

Tube Ref No.

Description

Where Used

Part No.

Engine Coupler Spline Grease

Driveshaft splines and U-joint

O-rings

92-802869A 1

2. For propeller shaft lubrication, refer to Propellers.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands