MerCruiser Axius 496 MAG H.O. Owner'S Manual Download

Page: 65 / 148

Section 3 - On The Water

90-899883154 JANUARY 2008

Page 57

2. Press the "AUTO HEADING" button to engage Axius. The button illuminates and a

single beep sounds. A double beep sounds if auto heading does not engage.

RESUME

STANDBY

ACTIVE

AUTO

HEADING

TURN

32507

a -

"AUTO HEADING" button

b -

Power icon

3. Axius holds the compass heading the boat is following when the "AUTO HEADING"

button is pressed.

31409

4. To make adjustments in the default heading while auto heading is active and the button

light is on, press the respective "TURN" button on the trackpad or tap (quickly move)

the joystick.

5. To make a turn:

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands