MerCruiser Axius 496 MAG H.O. Owner'S Manual Download | Manualshive

Page: 2 / 148

background image

Regulatory contact:

Engineering - Regulatory

MerCruiser

3003 N. Perkins Rd

Stillwater, Oklahoma 74075

USA

(405) 377-1200

Identification Record

Please record the following information:

Engine Model and Horsepower

Engine Serial Number

Transom Assembly Serial Number (Sterndrive)

Gear Ratio

Sterndrive Unit Serial Number

Transmission Model (Inboard)

Gear Ratio

Transmission Serial Number

Propeller Number

Pitch

Diameter

Hull Identification Number (HIN)

Purchase Date

Boat Manufacturer

Boat Model

Length

Exhaust Gas Emissions Certification Number

The serial numbers are the manufacturer’s keys to numerous engineering details that apply

to your Mercury MerCruiser® power package. When contacting your Authorized Mercury

MerCruiser Dealer about service,

always specify model and serial numbers.

The description and specifications contained herein were in effect at the time this guide

was approved for printing. Mercury Marine, whose policy is one of continuous

improvement, reserves the right to discontinue models at any time, or to change

specifications or designs, without notice and without incurring obligation.
Mercury Marine, Fond du Lac, Wisconsin, U.S.A. Printed in U.S.A.
© 2007, Mercury Marine
Mercury, Mercury Marine, MerCruiser, Mercury MerCruiser, Mercury Racing, Mercury

Precision Parts, Mercury Propellers, Mariner, Quicksilver, #1 On The Water, Alpha, Bravo,

Pro Max, OptiMax, Sport‑Jet, K‑Planes, MerCathode, RideGuide, SmartCraft, Zero Effort,

M with Waves logo, Mercury with Waves logo, and SmartCraft logo are all registered

trademarks of Brunswick Corporation. Mercury Product Protection logo is a registered

service mark of Brunswick Corporation.

Welcome

You have selected one of the finest marine power packages available. It incorporates

numerous design features to assure operating ease and durability.
With proper care and maintenance, you will thoroughly enjoy using this product for many

boating seasons. To ensure maximum performance and carefree use, we ask that you

thoroughly read this manual.

«
1
2
3
4
...
»

Summary of Contents for Axius 496 MAG H.O.





















































































































































Reviews:

No comments

Related manuals for Axius 496 MAG H.O.

Brand: O.S. engine Pages: 20

Brand: Kubota Pages: 285

Brand: MAK Pages: 2027

Brand: YOODA Pages: 7

Brand: Saito Pages: 27

3T-MOTORS 3T45-10E

Brand: 3T-Components Pages: 12

3T-MOTORS 3T35-13

Brand: 3T-Components Pages: 24

3T-MOTORS 3T35-10SD

Brand: 3T-Components Pages: 16

3T-MOTORS 3T35-10R

Brand: 3T-Components Pages: 20

Brand: Pentair Pages: 110

Brand: Kubota Pages: 47

Brand: Kubota Pages: 181

Brand: Volvo Penta Pages: 100

Brand: Volvo Penta Pages: 104

Brand: Lycoming Pages: 194

Brand: TJERNLUND Pages: 3

Brand: Detroit Diesel Pages: 39

Brand: Detroit Diesel Pages: 122

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands