MerCruiser Axius 496 MAG H.O. Owner'S Manual Download Page 91

Page: 91 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 83

1. Place the sterndrive unit in full down/in position.
2. Observe the oil level. Level must be between the "MIN" and "MAX" lines on the

reservoir.

7876

a -

Reservoir

b -

"MIN" and "MAX" lines

3. Fill as necessary with the specified fluid.

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering Fluid

Power trim pump

92-858074K01

Filling

1. Remove the fill cap from the reservoir.

NOTE: Fill cap is vented.

2. Add lubricant to bring level to the within the "MIN" and "MAX" lines on the reservoir.

Tube Ref No.

Description

Where Used

Part No.

114

Power Trim and Steering Fluid

Power trim pump

92-858074K01

3. Install the cap.

Changing

Power trim fluid does not require changing unless it becomes contaminated with water or

debris. Contact your authorized Mercury MerCruiser dealer.

Battery

Refer to specific instructions and warnings accompanying your battery. If this information

is not available, observe the following precautions when handling a battery.

WARNING

Recharging a weak battery in the boat, or using jumper cables and a booster battery to

start the engine, can cause serious injury or product damage from fire or explosion.

Remove the battery from the boat and recharge in a ventilated area away from sparks or

flames.

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands