background image

Section 1 - Warranty 

Page  4

90-899883154   JANUARY  2008

The Mercury Product Protection Plan provides coverage against unexpected mechanical

and electrical breakdowns that may occur beyond the standard limited warranty.
The optional Mercury Product Protection Plan is the only Factory Plan available for your

engine.
One‑, two‑, three‑, four‑, or five‑ year term plans can be purchased up to 12 months after

the original engine registration date.
See your participating Mercury MerCruiser dealer for complete program details.

Mercury MerCruiser Limited Warranty (Gasoline‑Fueled Products

Only)

MERCURY MERCRUISER LIMITED WARRANTY (GASOLINE-FUELED PRODUCTS ONLY)
What is Covered

Mercury Marine warrants its new products to be free of defects in material and workmanship during the period described following.

Duration of Coverage

Warranty Period for Recreational Use

The warranty period begins on the date the product is first sold to a recreational‑use retail purchaser or the date on which the

product is first put into service, whichever occurs first. Products installed by an Installation Quality Certified Installer receive one

(1) year of additional warranty coverage. The repair or replacement of parts or the performance of service under this warranty

does not extend the life of this warranty beyond its original expiration date. The warranty period is specific to the model covered;

see your model for the base coverage period:

Horizon Sterndrive and Inboard Models, and MX 6.2 Black Scorpion Tow Sport Model Coverage

The Limited Warranty for the Horizon Sterndrive and Inboard Models, and MX 6.2 Black Scorpion Tow Sport Models is

four (4) years when installed by an Installation Quality Certified Installer or three (3) years for noncertified installations.

SeaCore Sterndrive Model Coverage

The Limited Warranty for SeaCore Sterndrive Models is four (4) years when installed by an Installation Quality Certified

Installer or three (3) years for noncertified installations.

Standard Model Coverage

The Limited Warranty for Standard Models, which do not include Horizon Sterndrive and Inboard Models, MX 6.2 Black

Scorpion Tow Sport Models, or SeaCore Sterndrive Models, is two (2) years when installed by an Installation Quality

Certified Installer or one (1) year for noncertified installations.

Warranty Period for Commercial Use

The warranty period begins on the date the product is first sold to a commercial‑use retail purchaser or the date on which the

product is first put into service, whichever occurs first. Commercial users of these products receive warranty coverage for either

one (1) year from the date of first retail sale or the accumulation of 500 hours of operation, whichever occurs first. Commercial

use is defined as any work‑related or employment‑related use of the product, or any use of the product that generates income

for any part of the warranty period, even if the product is only occasionally used for such purposes. The repair or replacement

of parts or the performance of service under this warranty does not extend the life of this warranty beyond its original expiration

date.

Transfer of Coverage

Unexpired warranty coverage can be transferred from one recreational‑use customer to a subsequent recreational‑use customer

upon proper reregistration of the product. Unexpired warranty coverage cannot be transferred either to or from a commercial‑use

customer.

Termination of Coverage

Warranty coverage is terminated for used product obtained in any of the following ways:

Repossession from a retail customer

Purchase at auction

Purchase from a salvage yard

Purchase from an insurance company that obtained the product as a result of an insurance claim

Summary of Contents for Axius 496 MAG H.O.





















































































































































Reviews: