MerCruiser Axius 496 MAG H.O. Owner'S Manual Download

Page: 89 / 148

Section 5 - Maintenance

90-899883154 JANUARY 2008

Page 81

Tube Ref No.

Description

Where Used

Part No.

High Performance Gear

Lubricant

Gear lube monitor

92-858064K01

3. Replace the cap.

NOTE: When filling the entire sterndrive unit refer to Changing instructions, following.

Changing

1. Remove the gear lube monitor from the bracket.

8530

a -

Gear lube monitor

2. Empty the contents into a suitable container.
3. Install the gear lube monitor in the bracket.
4. Place the sterndrive unit in full up(out) position
5. Remove the oil fill/drain screw and sealing washer, and drain the oil into a suitable

container.

mc79507-1

a -

Oil fill/drain screw

b -

Sealing washer

Summary of Contents for Axius 496 MAG H.O.





















































































































































Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands

MerCruiser Axius 496 MAG H.O., Owner'S Manual

Search results

Summary of Contents for Axius 496 MAG H.O.

Reviews:

Related manuals for Axius 496 MAG H.O.

Brands by name

Popular brands