background image

It  is  of  vital  importance,  before  attempting  to 
operate  your  engine,    to  read  the  general 

'SAFETY  INSTRUCTIONS  AND  WARNINGS' 

section  on  pages  2-4  of  this  booklet  and  to 
strictly adhere to the advice contained therein.

Also, please study the entire contents of this 
instruction  manual,  so  as  to  familiarize 
yourself with the controls and other features of 
the engine.

Keep these instructions in a safe place so that 
you  may  readily  refer  to  them  whenever 
necessary.

It is suggested that any instructions supplied 
with the aircraft, radio control equipment, etc., 
are accessible for checking at the same time.

1

 

SAFETY INSTRUCTIONS AND 
WARNINGS ABOUT YOUR O.S. ENGINE

NOTES WHEN APPLYING AN 
ELECTRIC STARTER

ABOUT THE ENGINE

ENGINE PARTS NAME

RELOCATION OF CARBURETOR CONTROLS

FUEL TANK & LINES

INSTALLATION 

EXHAUST HEADER PIPE & SILENCER

PROPELLER

FUEL

CONTENTS

MIXTURE CONTROLS

STARTING

RUNNING-IN ("Breaking-in")

MAINTENANCE

ENGINE EXPLODED VIEW 

ENGINE PARTS LIST

CARBURETOR EXPLODED VIEW
& PARTS LIST

O.S. GENUINE PARTS & ACCESSORIES

ENGINE THREE VIEW DRAWINGS

2-4

5

6

7

8

9

10-11

12

13-14

15

16

17

18

19-21

22-23

24

25

26

27

28

GLOWPLUG

Содержание FS-200S
















Отзывы: