Maxim Integrated MAX32660 User Manual Download Page 189

Page: 189 / 195

MAX32660 User Guide

Maxim Integrated

Page 189 of 195

Table 14-5: SPIMSS Register Offsets, Access and Descriptions

Offset

Register Name

Access

Description

[0x0000]

SPIMSS_DATA

R/W

SPIMSS Data Register

[0x0004]

SPIMSS_CTRL

R/W

SPIMSS Control Register

[0x0008]

SPIMSS_INT_FL

R/W

SPIMSS Interrupt Flag Register

[0x000C]

SPIMSS_MODE

R/W

SPIMSS Mode Register

[0x0014]

SPIMSS_BRG

R/W

SPIMSS Bit Rate Register

[0x0018]

SPIMSS_DMA

R/W

SPIMSS DMA Register

[0x001C]

SPIMSS_I2S_CTRL

R/W

SPIMSS I

S Control Register

14.8.1

SPIMSS Register Details

Table 14-6. SPIMSS Data Register

SPIMSS Data Register

SPIMSS_DATA

[0x0000]

Bits

Name

Access

Reset

Description

31:16

R/W

Reserved for Future Use

Do not modify this field.

15:0

data

R/W

SPIMSS Data

Refer to the

SPI Data Movement

section for details.

Table 14-7: SPIMSS Control Register

SPIMSS Control Register

SPIMSS_CTRL

[0x0004]

Bits

Name

Access

Reset

Description

31:8

R/W

Reserved for Future Use

Do not modify this field.

irqe

R/W

Interrupt Request Enable

Set to enable interrupts for the SPIMSS peripheral.

0: SPIMSS (SPI1/I

S) interrupts are disabled.

1: SPI MSS (SPI1/I

S) interrupts are enabled. Interrupt requests are sent to the

Interrupt Controller

Note that if transmit or receive DMA is enabled, the transmit data complete
interrupt is disabled, but other interrupt sources are available.

str

R/W

Start SPI Interrupt

Setting this bit starts a SPIMSS interrupt request. Setting this bit also sets

SPIMSS_INT_FL

.irq

to 1. Setting this bit forces the SPIMSS to send an interrupt

request to the Interrupt Controller if

SPIMSS_CTRL

.irqe

= 1. This bit is cleared by

writing a 0 to this bit or by writing a 1 to

SPIMSS_INT_FL

.irq

birq

R/W

Bit Rate Generator Timer Interrupt Request

Enable or disable the Bit Rate Generator if the SPIMSS is enabled
(

SPIMSS_CTRL

enable

= 1).

0: Clearing this bit disables the Bit Rate Generation timer function.
1: Setting this bit to 1 enables the Bit Rate Generation timer function and

enables the time-out interrupt.

Note: If

SPIMSS_CTRL

.enable = 0, this bit has no effect.

Summary of Contents for MAX32660




































































































































































































Search results

Summary of Contents for MAX32660

Reviews:

Brands by name

Popular brands

Maxim Integrated MAX32660, User Manual

Search results

Summary of Contents for MAX32660

Reviews:

Brands by name

Popular brands