MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 160

Page: 160 / 178

Copyright by Servizio Clienti ANGELO PO Spa

160

6.14.5.

CPU board Replacing (2

version)

Before removing the CPU board, disconnect all the cables as shown in the picture

– Loudspeaker cable

– USB cable

– USB cable (optional)

– LCD display flat cable

– Encoder cable

– 24V power supply cable

– Communication cable (connection with

the power board)

– Keyboard flat cable (1

version)

– LED board flat cable (1

version)

9a - Keyboard flat cable (2

version)

9b - LED & Keyboard board flat cable (2

version)

– Connection with blast chiller (optional)

WARNING: DO NOT CONNECT THE POWER SUPPLY TO THE PLUG 10.

– Network cable (optional)

NOT IN USE

– CPU

– Keyboard

– Encoder

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands

MARMON ANGELO PO COMBISTAR FX, Technical Manual

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

Related manuals for ANGELO PO COMBISTAR FX

Brands by name

Popular brands