MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 172

Page: 172 / 178

Copyright by Servizio Clienti ANGELO PO Spa

172

Alarm on

display

Problem (on

the manual)

Solution (on the

manual)

Note (on the

manual)

Note for Service

E28

Valve not

working

Press reset button

The oven’s

functions are

enabled so

cooking

cycles can be

carried out.

Washing

programs are

disabled.

Check the connector terminals on the

valve and on the power board.

E29

Core probe not

inserted

Press reset button

The oven’s

functions are

enabled so

cooking

cycles can be

carried out.

---

E30

– E38

Electronic circuit

board

diagnostics

tripped.

Press reset button

If the problem

persists

inform the

after-sales

service.

Protections against electromagnetic

interferences. Check all the ground

wiring of the equipment. In case of gas

version, please check ignition electrode

and cover protections to be properly

fitted. Check all the wirings relative to

the ignition system. Check the correct

insulation of the cable.

E80

– E85

---

Inform the

after-sales

service.

---

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

MARMON ANGELO PO COMBISTAR FX, Technical Manual, Page: 172 / 178

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews: