MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 106

Page: 106 / 178

Copyright by Servizio Clienti ANGELO PO Spa

106

GAS alarm table

Alarm Code

PROBLEM

SOLUTION

E12:F10

Internal breakage of the combustion control

board

Replace the combustion control board

E12:F11

Flame signal detected before start

Check the wirings to the flame sensor. If

necessary replace the combustion control

board.

E12:F20

Flame signal detected after the stop.

Check the wirings to the flame sensor. If

necessary replace the combustion control

board.

E12:F24

Blower fan speed out of control or blower fan

blocked.

Check the power supply and control wirings to

the air blowing fan. If necessary replace the

blower fan.

E12:F26

Blower fan out of contro

l: the blower fan doesn’t

stop after 30 seconds from its off.

Check the correct wirings to the blower fan. If

necessary replace the combustion control

board.

E12:F30

Operating parameters of the combustion control

board corrupted.

Replace the combustion control board.

Note:

Starting SW version 1.11 the general gas alarm has been changed from the word

“GAS” into E12

Note:

For the 20 grid models appears with the alarm also the number of the burner; 1

stands for the lower burner and 2 stands for the upper burner.

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews:

MARMON ANGELO PO COMBISTAR FX, Technical Manual, Page: 106 / 178

Search results

Summary of Contents for ANGELO PO COMBISTAR FX

Reviews: