manualshive.com logo in svg

MARMON ANGELO PO COMBISTAR FX, Technical Manual, Page: 90 / 178

Share
Download
MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 90

 

Copyright by Servizio Clienti ANGELO PO Spa 

 

90 

5.  Now you are into the gas setup: Step 1: 

-

  check correct ignition 

-

  Verify the stability of the minimum power 

-

  Check combustion values (CO, CO2) with oven cold 

-

  Fill in the installation report with the values found 

 

6.  Step 2:  

-

  Verify the stability of the maximum power 

-

  Check  combustion  values  (CO,  CO2)  at  maximum 

power 

-

  Fill in the installation report with the values found 

 

7.  Step 3:  

-

  Verify the correct ignition 

-

  Verify the stability of the minimum power with the oven 

warm 

-

  combustion values (CO, CO2) at minimum power with 

the oven warm 

-

  Fill in the installation report with the values found 

For  the  flue  gases  analysis  see  section  4.6.  Combustion 

products analysis. 

The  screen  shows  the  parameters  that  govern  the  blower  (Minimum  speed,  Maximum 

Speed, Ignition Speed), in addition to the speed to be achieved (set point) and the actual 

speed.  Verify  that  the  ignition  occurs  at  the  correct  speed  and  that  the  minimum  and 

maximum speeds reached match those settings. 

If the gas system doesn’t function properly or the flue combustion values are not included 

in the ranges indicated, follow the instructions in section 4.4.4.1 Adjustments. 

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Reviews:

No comments