manualshive.com logo in svg

MARMON ANGELO PO COMBISTAR FX, Technical Manual, Page: 145 / 178

Share
Download
MARMON ANGELO PO COMBISTAR FX Technical Manual Download Page 145

 

Copyright by Servizio Clienti ANGELO PO Spa 

 

145 

The sealing system inside the room (frame/glass/seal) remains unchanged. The assembly 
needs the use of silicon as now.

 

 

 

 

   

 

 
 

6.9.2. 

Bulb replacement with the new system 

Replacement lamp with the new system can be done in two different ways: 

 
1) From the internal side 
 
Removing frame, glass and gasket from the inside ... The lamp holder and its frame 

remain in place thanks to the two studs. The operation can be performed by one person. 

 

2) From the external side 

 

Loose the 4 screws (inside the room) that hold the frame until it detaches from the 

threaded inserts.  On the outside, remove the two nuts onto the threaded pins and 

removing the group frame + lamp holder. 

Summary of Contents for ANGELO PO COMBISTAR FX



















































































































































































Reviews:

No comments